B&R Industrial Automation (a Business Unit of ABB) X20SI8110
X20SI8110: 8 safe digital inputs; 4 pulse outputs; Sink circuit; Software input filter configurable for each channel; Single-width module; This single-width module is equipped with 8 safe digital inputs. It is designed for a nominal voltage of 24 VDC.; The module can be used to read various digital signals in safety-related applications up to PL e or SIL 3.; The module is equipped with filters that are individually configurable for switch-on and switch-off behavior. The module also provides pulse signals for diagnosing the sensor line.; This module is designed for X20 12-pin terminal blocks.
Категории:
Технические характеристики
| I/O module | 8 safe type A digital inputs, 4 pulse outputs, 24 VDC |
|---|---|
| B&R ID code | 0xE742 |
| Automation Studio | 4.0 or later |
| Automation Runtime | 4.0 or later |
| SafeDESIGNER | 3.4.0 or later |
| Safety Release | 1.7 or later |
| Status indicators | I/O function per channel, operating state, module status |
| Module run/error | Yes, using LED status indicator and software |
| Inputs | Yes, using LED status indicator and software |
| Scope | Module |
| Function | Module function |
| Standalone mode | No |
| Max. I/O cycle time | 1 ms |
| Bus | 0.4 W |
| Internal I/O | 2.5 W |
| Additional power dissipation caused by actuators (resistive) [W] | 0.8 |
| Channel - Bus | Yes |
| Channel - Channel | No |
| CE | Yes |
| Functional safety | EN 50156-1:2004 |
| ATEX | Zone 2, II 3G Ex nA nC IIA T5 GcIP20, Ta (see X20 user's manual)FTZÚ 09 ATEX 0083X |
| UL | cULus E115267Industrial control equipment |
| DNV GL | In preparation |
| EAC | Yes |
| Category | Cat. 3 when using individual input channels,Cat. 4 when using input channel pairs (e.g. SI1 and SI2) or more than 2 input channels |
| PL | PL e |
| DC | >94% |
| MTTFD | 2500 years |
| Mission time | Max. 20 years |
| SIL CL | SIL 3 |
| SFF | >90% |
| Module | <1*10-10 |
| openSAFETY wired | Negligible |
| openSAFETY wireless | <1*10-14* Number of openSAFETY packets per hour |
| PFD | <2*10-5 |
| Proof test interval (PT) | 20 years |
| Напряжение питания | 24 VDC |
| Напряжение питания | 24 VDC -15% / +20% |
| Integrated protection | Reverse polarity protection |
| Quantity | 4 |
| Variant | Push-Pull |
| Input characteristics per EN 61131-2 | Type 1 |
| Hardware | ≤150 μs |
| Software | Configurable between 0 and 500 ms |
| Input circuit | Sink |
| Напряжение питания | 24 VDC -15% / +20% |
| Input current at 24 VDC | Max. 3.28 mA |
| Input resistance | Min. 7.33 kΩ |
| Error detection time | 100 ms |
| Напряжение питания | 500 Veff |
| Low | <5 VDC |
| High | >15 VDC |
| Cable length between signal source (pulse output or external signal) and input | Max. 60 m with unshielded lineMax. 400 m with shielded line |
| Nominal output current | 50 mA |
| Output protection | Shutdown of individual channels in the event of overload or short circuit |
| Peak short-circuit current | 0.5 A for 120 µs |
| Short-circuit current | 15 mAeff |
| Leakage current when the output is switched off | 0.1 mA |
| RDS(on) | 80 Ω |
| Напряжение питания | I/O power supply minus voltage drop due to RDS(on) |
| Total nominal current | 200 mA |
| Horizontal | Yes |
| Vertical | Yes |
| Installation elevation above sea level | 0 to 2000 m, no limitation |
| Degree of protection per EN 60529 | IP20 |
| Horizontal mounting orientation | 0 to 60°C |
| Vertical mounting orientation | 0 to 50°C |
| Derating | See section "Derating". |
| Storage | 5 to 95%, non-condensing |
| Transport | 5 to 95%, non-condensing |
| Operation | 5 to 95%, non-condensing |
| Note | Order 1x safety-keyed terminal block separately.Order 1x safety-keyed bus module (single-width) separately. |
| Pitch | 12.5+0.2mm |