ifm electronic gmbh SUH320
Ultrasonic flow meter, SUC40XJBFRKG/US
Технические характеристики
| Measuring range | -40...130 °C: -40...266 °F |
|---|---|
| Nominal diameter | DN40 (1 1/2“) |
| Process connection | Clamp DN40 DIN 32676 series A |
| Special feature | gold-plated contacts |
| Application | food and beverage industry |
| Media | ultra-pure water; water; water-based media; edible oils |
| Note on media | water-based media: for media with >10 % additives, the repeatability is the only available value; edible oils: palm oil, soy oil, rapeseed oil, sunflower oil, peanut oil, olive oil and others |
| Medium temperature [°C] | -40...130; (< 1 h: 150) |
| Min. burst pressure | 75 bar: 7.5 MPa |
| Pressure rating | 25 bar: 2.5 MPa |
| Note on pressure rating | take into account the pressure resistance of the bracket and the seal used for clamp connection |
| Vacuum resistance [mbar] | -1000 |
| Напряжение питания | 18...32 DC; (to SELV/PELV) |
| Current consumption [mA] | < 75 |
| Protection class | III |
| Reverse polarity protection | yes |
| Power-on delay time [s] | 5 |
| Measuring principle | ultrasonic |
| Inputs | OUT2: counter reset |
| Total number of outputs | 2 |
| Output signal | OUT1: switching signal; pulse signal; diagnostic signal; totalizer switching signal; frequency signal; IO-Link; OUT2: switching signal; pulse signal; diagnostic signal; totalizer switching signal; analog signal |
| Electrical design | PNP/NPN |
| Output function | normally open / closed; (configurable) |
| Pulse output | flow rate meter |
| Short-circuit protection | yes |
| Type of short-circuit protection | yes (non-latching) |
| Overload protection | yes |
| Number of analog outputs | 1 |
| Analog current output [mA] | 4...20 |
| Max. load [Ω] | 500 |
| Number of digital outputs | 2 |
| Напряжение питания | 2 |
| Permanent current rating of switching output DC [mA] | 100 |
| Switching frequency DC [Hz] | 0...10000 |
| Resolution | 0.1 °C: 0.1 °F |
| Note on factory setting | l/min, °C |
| Set point SP | -39.4...130 °C: -38.9...266 °F |
| Reset point rP | -40...129.4 °C: -40...264.9 °F |
| Analog start point ASP | -375...300 l/min: -22.5...18 m³/h: -5944...4755 gph: -99.06...79.25 gpm |
| Analog end point AEP | -300...375 l/min: -18...22.5 m³/h: -4755...5944 gph: -79.25...99.06 gpm |
| Low flow cut-off LFC | 3...18.8 l/min: 0.18...1.125 m³/h: 48...297 gph: 0.79...4.95 gpm |
| Frequency end point, FEP | -6...130 °C: 21.2...266 °F |
| Frequency at the end point FRP [Hz] | 1...10000 |
| Pulse length [s] | 0.002...2 |
| Pulse value | 0.1...99990000 I; 0.03…26414563.515 gal |
| Analog start point | -40...96 °C: -40...204.8 °F |
| Analog end point | -6...130 °C: 21.2...266 °F |
| Frequency start point, FSP | -40...96 °C: -40...204.8 °F |
| Accuracy (in the measuring range) | water: ± (1,0 % MW + 0,5 % MEW) |
| Repeatability | ± 0,2 % MEW |
| Accuracy [K] | ± 2,5 (Q > 5 % MEW) |
| Temperature coefficient [% of the span / 10 K] | 0,2 |
| Время отклика | < 0.3; (dAP = 0, T09) |
| Damping process value dAP [s] | 0...5 |
| Dynamic response T05 / T09 [s] | 5,7 / 86 |
| Diagnostic functions | direction of flow detection; signal quality |
| Communication interface | IO-Link |
| Transmission type | COM2 (38,4 kBaud) |
| IO-Link revision | 1.1.3 |
| SDCI standard | IEC 61131-9: 2013-07 |
| Profiles | BLOB: Binary Large Object transfer; Common - I&D: Identification and Diagnosis |
| Required master port class | A |
| Process data analog | 3 |
| Process data binary | 2 |
| Min. process cycle time [ms] | 9.6 |
| IO-Link process data (cyclical) | Function: bit length; totalizer: 32; Flow monitoring: 32; Temperature monitoring: 32; status: 4; Output 1: 1; Output 2: 1 |
| Supported DeviceIDs | Type of operation: DeviceID; default: 1910 |
| Рабочая температура | -20...60 |
| Storage temperature [°C] | -25...80 |
| Protection | IP 69; (DIN EN 60529) |
| EMC | DIN 61326-1:2021 |
| Shock resistance | DIN IEC 68-2-27: 20 g (11ms) |
| Vibration resistance | DIN IEC 68-2-6: 20 g (10...2000Hz) |
| MTTF [years] | 160 |
| UL approval | UL approval number: I038; File number UL: E174189 |
| Pressure equipment directive | can be used for group 2 fluids; group 1 fluids on request |
| Масса | 835.5 |
| Housing | rectangular |
| Inlet pipe length | 5 x DN |
| Outlet pipe length | 1 x DN |
| Dimensions [mm] | 220 x 50.5 x 74.9 |
| Материал | housing: stainless steel (1.4404 / 316L); connector: PEI, FKM |
| Материал | Pipe section: stainless steel (1.4435 / 316L); Process connection: stainless steel (1.4404 / 316L) |
| Process connection suitable for pipe standard | DN40 / Ø 41 mm x 1.5 mm; (DIN 11866 series A); (DIN EN 10357 series A) |
| Surface characteristics Ra/Rz of the wetted parts | Ra < 0.4 µm (16 µin); Rz = 4 µm (157 µin) |
| Display | operating status: 1 x LED, green |
| Items supplied | package insert |
| Remarks | MW = Measured value; MEW = Final value of the measuring range; pulse and totalizer signal are only available for one of the two outputs; the specified surface characteristics Ra/Rz of the wetted surfaces do not apply to the weld seam. |
| Pack quantity | 1 pcs. |
| Connector | 1 x M12; coding: A; Contacts: 4, gold-plated |