KE
KEYENCE CORPORATION LJ-G5001
LJ-G5000 series (2D лазерный датчик перемещения) - LJ-G5001
Категории:
Технические характеристики
| Head compatibility | Measuring units are interchangeable without factory recalibration. |
|---|---|
| Number of connectable sensors | Maximum of 2 units |
| Display (Minimum display unit) | 0.1 µm , 0.001 mm 2 , 0.01° (Inch mode : 0.01 Mil, 0.00001 inch ) |
| Display (Maximum display range) | ±99999.9 mm, ±999999 mm 2 , ±99999.9° (Inch mode : ±9999.99 Mil, ±999.999 inch ) |
| Input terminal block (Laser remote interlock input) | Non-voltage or voltage input . |
| Input terminal block (Trigger input) | For sensor head A, non-voltage input |
| Input terminal block (Timing 1 input) | Non-voltage input |
| Напряжение питания | ±10 V x 2 outputs, output impedance: 100 Ω |
| Output terminal block (Total judgment output) | NPN open-collector output |
| Output terminal block (Error output) | NPN open-collector output (N.C.) |
| Output terminal block (Process output) | NPN open-collector output |
| Output terminal block (Trigger input enable output) | For sensor head A, NPN open-collector output |
| Expansion connector (Timing 2 input) | Non-voltage input |
| Expansion connector (Trigger input) | For sensor head B, non-voltage input |
| Expansion connector (Program switching input) | Non-voltage input, 4 inputs |
| Expansion connector (Memory card save input) | Non-voltage input |
| Expansion connector (Laser-Off input) | For sensor head A/B, non-voltage input |
| Expansion connector (Judgment/Binary output) | 3-level judgment output: OUT1 to OUT8, total judgment output Binary output: OUT1 to OUT8 measured data output (21 bits) NPN open-collector output |
| Expansion connector (Strobe output) | NPN open-collector output |
| Expansion connector (Trigger input enable output) | For sensor head B, NPN open-collector output |
| Analog RGB monitor output | SVGA (800 × 600 pixels) |
| RS-232C interface | Measured data output and control input/output (Maximum baud rate: 115200 bps, selectable) |
| USB interface | Supports USB 2.0 Hi-Speed (compatible with USB 1.1 Full Speed) |
| Ethernet interface | 100BASE-TX/10BASE-T |
| Memory card | Compatible with NR-M1G (1 GB). (with FAT32) |
| Major functions | Sensor heads calculation, Profile adjustment, Filter, Smoothing, Averaging, Position adjustment, OUT name change, Measurement mode selection (Height, position, gap, width, center position, section area, intersection, angle, profile comparison, profile tracking), Scaling, Average, Measurement, Measured value alarm, Tolerance setting, Auto-zero, Storage (data/profile), Memory card saving, Program memory, Trigger mode change, Mutual interference prevention, Measuring range change, Calibration, Laser light adjustment, Sampling time setting, Mask, Profile alarm setting, Inclination adjustment, Height adjustment, Display language switch, Setting support software connection, Trigger pitch/Measuring time display, etc. |
| Напряжение питания | 24 VDC ±10 %, Ripple (P-P) 10 % or less |
| Rating (Current consumption) | 800 mA or less with 1 sensor head/1 A or less with two sensor heads |
| Рабочая температура | 0 to +50 °C 32 to 122 °F |
| Environmental resistance (Relative humidity) | 35 to 85 % RH (No condensation) |
| Масса | Approx. 1,050 g |