Mitsubishi Electric Corporation (Factory Automation / FA Systems Group) QS001CPU-K
QS001CPU-K
Технические характеристики
| Control method | Stored program cyclic operation |
|---|---|
| I/O control mode | Refresh mode |
| Sequence control language | Relay symbol language, function block |
| LD X0 | 0.10 µs |
| MOV D0 D1 | 0.35 µs |
| Constant scan | 1...2000 ms (setting is available in increments of 1 ms by parameter) |
| Program capacity | 14K steps (56K bytes) |
| Program memory (drive 0) | 128K bytes |
| Standard ROM (drive 4) | 128K bytes |
| Program memory | 3 |
| Standard ROM | 3 |
| No. of data writing times into the standard ROM | Maximum 100,000 times |
| Number of I/O device points | 6144 points (X/Y0...17FF) |
| Number of I/O points | 1024 points (X/Y0...3FF) |
| Internal relay (M) | 6144 points (M0...6143) by default (changeable) |
| Link relay (B) | 2048 points (B0...7FF) by default (changeable) |
| Timer (T) | 512 points (T0...511) by default (changeable) (Low-speed and high-speed timers available) Low-speed or high-speed is specified by an instruction. The measurement unit is set by parameter. (Low-speed timer: 1...1000 ms (in increments of 1 ms), default: 100 ms) (High-speed timer: 0.1...100.0 ms (in increments of 0.1 ms), default: 10.0 ms) |
| Retentive timer (ST) | 0 points by default (changeable) (Low-speed and high-speed retentive timers available) Low-speed or high-speed is specified by an instruction. The measurement unit is set by parameter. (Low-speed retentive timer: 1...1000 ms (in increments of 1 ms), default: 100 ms) (High-speed retentive timer: 0.1...100.0 ms (in increments of 0.1 ms), default: 10.0 ms) |
| Counter (C) | Normal counter: 512 points (C0...511) by default (changeable) |
| Data register (D) | 6144 points (D0...6143) by default (changeable) |
| Link register (W) | 2048 points (W0...7FF) by default (changeable) |
| Annunciator (F) | 1024 points (F0...1023) by default (changeable) |
| Edge relay (V) | 1024 points (V0...1023) by default (changeable) |
| Link special relay (SB) | 1536 points (SB0...5FF) (The number of device points is fixed.) |
| Link special register (SW) | 1536 points (SW0...5FF) (The number of device points is fixed.) |
| Special relay (SM) | 5120 points (SM0...5119) (The number of device points is fixed.) |
| Special register (SD) | 5120 points (SD0...5119) (The number of device points is fixed.) |
| RUN/PAUSE contact | One contact can be set up in X0 to X17FF for each of RUN. No PAUSE contact. |
| Clock function | Year, month, date, hour, minute, second, and day of week (automatic leap year detection) Accuracy: -3.18...+5.25 s (TYP. +2.14 s)/d at 0 ˚C Accuracy: -3.18...+2.59 s (TYP. +2.07 s)/d at 25 ˚C Accuracy: -12.97...+3.63 s (TYP. -3.16 s)/d at 55 ˚C |
| Allowable momentary power failure time | The time differs depending on the power supply module used. |
| Internal current consumption (5 V DC) | 0.58 A |
| Height | 98 mm |
| Width | 55.2 mm |
| Depth | 114 mm |
| Масса | 0.30 kg |
| Protection degree | IP2X |
| Рабочая температура | 0...55 ˚C |
| Storage ambient temperature | -40...75 ˚C |
| Operating ambient humidity | 5...95 %RH, non-condensing |
| Storage ambient humidity | 5...95 %RH, non-condensing |
| Under intermittent vibration | Frequency: 5...8.4 Hz, Half amplitude: 3.5 mm Frequency: 8.4...150 Hz, Constant acceleration: 9.8 m/s 2 Sweep count: 10 times each in X, Y, Z directions |
| Under continuous vibration | Frequency: 5...8.4 Hz, Half amplitude: 1.75 mm Frequency: 8.4...150 Hz, Constant acceleration: 4.9 m/s 2 |
| Shock resistance | Compliant with JIS B 3502 and IEC 61131-2 (147 m/s 2 , duration of action 11 ms, 3 times in X, Y, Z directions respectively by sine half-wave pulse) |
| Operating atmosphere | No corrosive gases |
| Operating altitude | 0...2000 m |
| Installation location | Inside a control panel |
| Напряжение питания | II or less |
| Pollution degree | 2 or less |
| Equipment class | Class I |
| Category (site listing) | CPU |