Mitsubishi Electric Corporation (Factory Automation / FA Systems Group) QS0J65BTS2-4T
QS0J65BTS2-4T
Технические характеристики
| Number of output points | 4 points (source + sink type) 2 points (source + source type) |
|---|---|
| Напряжение питания | 24 V DC |
| Напряжение питания | 19.2...28.8 V DC (ripple ratio: within 5 %) |
| Maximum load current | 0.5 A/point |
| Maximum inrush current | 1.0 A, 10 ms or less |
| Leakage current at OFF | 0.5 mA or less |
| Напряжение питания | 1.0 V DC or less |
| Protection function | Output overload protection function |
| Output type | Source + sink type Source + source type |
| OFF to ON | 0.4 ms or less (24 V DC) |
| ON to OFF | 0.4 ms or less (24 V DC) |
| Время отклика | 11.2 ms or less |
| Время отклика | 10.4 ms or less |
| Surge suppressor | Zener diode |
| Output common terminal arrangement | 4 points/common (2-wire, spring clamp terminal block type) |
| Common current | Maximum 2 A |
| Output isolation method | Photocoupler |
| Напряжение питания | Between all DC external terminals and ground: 500 V AC for 1 minute |
| Insulation resistance | Between all DC external terminals and ground: 10 MΩ or higher by 500 V DC insulation resistance tester |
| Protection degree | IP2X |
| Station type | Safety remote I/O station |
| Number of occupied stations | 1 station |
| Number of accesses to nonvolatile memory inside module | 10 12 times |
| Время отклика | 9.6 ms |
| Напряжение питания | 19.2...28.8 V DC (ripple ratio within 5 %) |
| Current | 45 mA (at 24 V DC and all points ON, excluding the external load current) |
| External power supply > Protection function | External power supply overvoltage protection function, external power supply overcurrent protection function |
| Fuse | 8 A (not replaceable) |
| Напряжение питания | 19.2...28.8 V DC (ripple ratio: within 5 %) |
| Module power supply > Current | 95 mA or less (at 24 V DC, all points ON) |
| Module power supply > Protection function | Module power supply overvoltage protection function, module power supply overcurrent protection function |
| Module power supply > Fuse | 0.8 A (not replaceable) |
| Allowable momentary power failure time | Within 10 ms |
| External interface | Communication part, module power supply part: 7-point two-piece terminal block (M3 screw) I/O power supply part, I/O part: two-piece spring clamp terminal block |
| Масса | 0.45 kg |
| Рабочая температура | 0...55 ˚C |
| Storage ambient temperature | -40...75 ˚C |
| Operating ambient humidity | 5...95 %RH, non-condensing |
| Storage ambient humidity | 5...95 %RH, non-condensing |
| Under intermittent vibration | Frequency: 5...8.4 Hz, Half amplitude: 3.5 mm Frequency: 8.4...150 Hz, Constant acceleration: 9.8 m/s 2 Sweep count: 10 times each in X, Y, Z directions |
| Under continuous vibration | Frequency: 5...8.4 Hz, Half amplitude: 1.75 mm Frequency: 8.4...150 Hz, Constant acceleration: 4.9 m/s 2 |
| Shock resistance | Compliant with JIS B 3502 and IEC 61131-2 (147 m/s 2 , duration of action 11 ms, 3 times in X, Y, Z directions respectively by sine half-wave pulse) |
| Operating atmosphere | No corrosive gases |
| Operating altitude | 0...2000 m |
| Installation location | Inside a control panel |
| Напряжение питания | II or less |
| Pollution degree | 2 or less |
| Equipment class | Class III |
| Category (site listing) | Safety network |