Pepperl+Fuchs SE NBN25-F135-L4-M18-30M-SET
Inductive Sensor Kit
Категории:
Технические характеристики
| Switching function | Normally open/closed (NO/NC) programmable |
|---|---|
| Output type | PNP |
| Rated operating distance | 25 mm |
| Installation | flush mountable |
| Output polarity | DC |
| Assured operating distance | 0 ... 20 mm |
| Actuating element | Steel Fe360 , 75 mm x 75 mm x 1 mm |
| Reduction factor rAl | 0.7 |
| Reduction factor rCu | 0.7 |
| Reduction factor r304 | 0.6 |
| Reduction factor rBrass | 1.1 |
| Напряжение питания | 10 ... 30 V |
| Switching frequency | 0 ... 30 Hz |
| Hysteresis | typ. 5 % |
| Reverse polarity protection | reverse polarity protected |
| Short-circuit protection | pulsing |
| Напряжение питания | ≤ 3 V |
| Operating current | 0 ... 200 mA |
| Off-state current | 0 ... 0.5 mA typ. 0.1 µA |
| No-load supply current | ≤ 40 mA |
| Power consumption | ≤ 420 mW |
| Time delay before availability | ≤ 300 ms |
| Status indicator | Dual color-LED, yellow/greenSIO mode:yellow = switching stategreen = power supply onIO-Link mode:see manual |
| Interface type | IO-Link ( via C/Q = pin 4 ) |
| IO-Link revision | 1.1 |
| Device profile | Identification and Diagnosis - I&DSmart Sensor - SSP 1.1 |
| Process data | Input 5 Bit- switching signal 1 Bit- uncertainty indication 1 Bit- status signal 1 Bit- maintenance warning 1 Bit |
| Vendor ID | 1 (0x0001) |
| Device ID | 2098689 (0x200601) |
| Transfer rate | COM2 (38.4 kBit/s) |
| Min. cycle time | 2.3 ms |
| SIO mode support | yes |
| Compatible master port type | Class AClass B (use 3-pole adapter or 3-wire cable) |
| Designation | Sync |
| Input/output type | 1 synchronization connection, bidirectional |
| PWIS conformity | VDMA24364-B1/B2/C1/T220°C-W |
| Standard conformity - Standards | EN IEC 60947-5-2:2020EN IEC 60947-5-2:2020-03 /RoHs-II |
| Standard conformity - Communication interface | IEC 61131-9 / IO-Link V1.1.3 |
| Protection class | III |
| Напряжение питания | 36 V |
| Напряжение питания | 500 V |
| UL approval | cULus Listed, General Purpose, Class 2 Power Source |
| CCC approval | CCC approval / marking not required for products rated ≤36 V |
| Рабочая температура | 0 ... 250 °C (32 ... 482 °F)Note: M8 connector, 4-pin 0 ... 70 °C (32 ... 158 °F) |
| Storage temperature | 0 ... 70 °C (32 ... 158 °F) |
| Vibration resistance | 30 g |
| Connection type | Connector plug |
| Degree of protection | Sensor head: IP65amplifier: IP67connection cable: IP50 |
| Материал | Sensor head: PEEK 450, 30% fibre glassamplifier: Stainless steel 1.4305 / AISI 303 |
| Материал | Mounting bracket made of aluminum 3.3206 |
| Connector - Threading | M12 x 1 |
| Connector - Number of pins | 4 |
| Connector - Connection assembly | additional M8 plug connector on the sensor head sideCordset M8 plug straight A-coded 4-pin to LEMO-socket straight 4-pin, PFA cable black, shielded |
| Cable - Cable diameter | 3.9 mm |
| Cable - Bending radius | fixed installation 7.5 x cable diametermovable installation 15 x cable diameter |
| Материал | PFA |
| Cable - Color | black |
| Cable - Number of cores | 3 |
| Cable - Core cross section | 0.34 mm2 |
| Cable - Shield | grid |
| Cable - Length | 30.2 mindividual length specifications:sensor head cable: 0.2 mconnection cable: 30 m |
| Mass | 1305 g |
| Dimensions - Height | 44 mm Sensor head |
| Dimensions - Width | 40 mm Sensor head |
| Dimensions - Length | 67 mm Sensor head |
| Mounting | amplifier: nuts, M18 |
| Tightening torque | ≤ 30 Nm |
| Default setting | PNP, NO |
| Scope of delivery | 2 self locking nuts in scope of delivery |