Pepperl+Fuchs SE NCB40-FP-N0-P4
Inductive sensor
Категории:
Технические характеристики
| Switching function | Normally closed (NC) |
|---|---|
| Output type | NAMUR |
| Rated operating distance | 40 mm |
| Installation | flush |
| Assured operating distance | 0 ... 32 mm |
| Actual operating distance | 36 ... 44 mm typ. 40 mm |
| Reduction factor rAl | 0.35 |
| Reduction factor rCu | 0.35 |
| Reduction factor r304 | 0.8 |
| Напряжение питания | 8.2 V (Riapprox. 1 kΩ) |
| Switching frequency | 0 ... 80 Hz |
| Hysteresis | 0 ... 5 % typ. 3 % |
| Reverse polarity protection | reverse polarity protected |
| Short-circuit protection | yes |
| Current consumption - Measuring plate not detected | ≥ 3 mA |
| Current consumption - Measuring plate detected | ≤ 1 mA |
| Time delay before availability | ≤ 20 ms |
| Switching state indicator | LED, yellow |
| Standard conformity - NAMUR | EN 60947-5-6:2000IEC 60947-5-6:1999 |
| Standard conformity - Electromagnetic compatibility | NE 21:2007 |
| Standard conformity - Standards | EN IEC 60947-5-2 |
| IECEx approval - Equipment protection level Ga | IECEx PTB 11.0021X |
| IECEx approval - Equipment protection level Gb | IECEx PTB 11.0021X |
| IECEx approval - Equipment protection level Da | IECEx PTB 11.0021X |
| ATEX approval - Equipment protection level Ga | PTB 00 ATEX 2032 X |
| ATEX approval - Equipment protection level Gb | PTB 00 ATEX 2032 X |
| ATEX approval - Equipment protection level Da | PTB 00 ATEX 2032 X |
| UL approval | cULus ListedLoad Type: General PurposeCircuitry: Class 2 Power SourceEnclosure Type Rating: Type 1Supply/Switching Voltage: 8.2 V DC |
| ATEX approval - Ordinary Location | E87056 |
| ATEX approval - Hazardous Location | E501628 |
| ATEX approval - Control drawing | 116-0451 |
| CCC approval - Hazardous Location | 2020322315002304 |
| CML approval | on request |
| Рабочая температура | -25 ... 100 °C (-13 ... 212 °F) |
| Storage temperature | -40 ... 100 °C (-40 ... 212 °F) |
| Connection type | screw terminals |
| Information for connection | A maximum of two conductors with the same core cross section may be mounted on one terminal connection!tightening torque 1.2 Nm + 10 % |
| Core cross section | up to 2.5 mm2 |
| Minimum core cross-section | without wire end ferrules 0.5 mm2, with connector sleeves 0.34 mm2 |
| Maximum core cross-section | without wire end ferrules 2.5 mm2, with connector sleeves 1.5 mm2 |
| Материал | PBT/metal |
| Sensing face | PBT |
| Housing base | aluminum painted |
| Degree of protection | IP67 |
| Mass | 572 g |
| Dimensions - Height | 40 mm |
| Dimensions - Width | 83 mm |
| Dimensions - Length | 83 mm |
| Note | Tightening torque: 1.8 Nm (housing) |
| Use in the hazardous area | see instruction manuals |